白云石制备似立方体状方解石型碳酸钙晶体及其机理研究

以轻烧白云石粉、氯化铵和二氧化碳为原料,在未使用晶型控制剂的情况下,通过蒸氨-沉钙过程制备出了似立方体状碳酸钙。研究了反应温度、溶液中钙离子浓度、通气速率、搅拌速度以及陈化时间对碳酸钙中方解石相含量以及晶体形貌的影响,并探索了沉钙反应的晶型控制机理。结果表明,在反应温度40 ℃、钙离子浓度0.05 mol/L、通碳速率100 mL/min、搅拌速度400 r/min和陈化时间2 h的条件下,制备出形貌规整、粒径分布均匀的似立方体状碳酸钙,平均粒径为5~10 μm。该研究为提升白云石的使用价值、生产高附加价值的碳酸钙产品,以及提高白云石资源的利用率提供理论基础。     

Validation of quartz crystal rheometry in the megahertz frequency regime

The utility of the quartz crystal microbalance (QCM) as a high‐frequency rheometer operating at 15 MHz was demonstrated. High‐frequency data obtained from a series of rubbery materials were compared with results obtained from traditional dynamic mechanical analysis (DMA) at much lower frequencies. The high‐frequency data enable meaningful shift factors to be obtained at temperatures much further above glass‐transition temperature (T _g) than would otherwise be possible, giving a more complete picture of the temperature dependence of the viscoelastic properties. The QCM can also be used to quantify mass uptake and changes in viscoelastic properties during sample oxidation. The viscoelastic response spanning the full range of behaviors from the rubber to glassy regimes was found to fit well with a six‐element model consisting of three power‐law springpot elements. One of these elements is particularly sensitive to the behavior in the transition regime where the phase angle is maximized. The value of this quantity is obtained from the maximum phase angle, which can be obtained from a temperature sweep at fixed frequency, proving a means for more detailed frequency‐dependent rheometric information to be obtained from a fixed‐frequency measurement at a range of temperatures. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1246–1254     

Stabilization of a viscoelastic rotating Euler‐Bernoulli beam

In this paper, we consider a rotating Euler‐Bernoulli beam. The beam is made of a viscoelastic material, and it is subject to undesirable vibrations. Under a suitable control torque applied at the motor, we prove the arbitrary stabilization of the system for a large class of relaxation functions by using the multiplier method and some ideas introduced by Tatar (J. Math. Phys. 52:013502, 2011).     

金属Al背电极二维AZO光栅的制备和陷光特性

研究了背电极金属Al膜上二维ZnO:Al光栅的制备及其反射光谱特性.在厚度为300 nm的Al膜上溅射80 nm ZnO:Al薄膜,旋涂AZ5206光刻胶,用波长为325 nm的激光进行光刻制作光栅掩模.采用溶脱-剥离法在Al衬底上制备周期(624~1250 nm)和槽深(100~300 nm)可独立调控的ZnO:Al二维光栅.表面形貌采用原子力显微镜和扫描电镜观察,反射光谱用带积分球的分光光度计测试,双向反射分布函数用散射仪测量.结果表明,300 nm Al膜上织构二维ZnO:Al光栅背电极结构,当光栅槽深为228 nm,周期从624 nm增加到986 nm时,背电极总反射率、漫反射率以及雾度均随光栅周期增大而显著增加,而当周期从986 nm增加到1250 nm时,总反射率、漫反射率以及雾度略有增加.双向反射分布函数测试结果进一步证实了上述实验结果,即随着周期增大,漫反射峰值越大,衍射峰个数也增多.提示背反电极上槽深为228 nm、周期为986 nm的二维ZnO:Al光栅具有较好的散射效果,其中漫反射占总反射的百分比为45%.     

Interface effect between blue phosphorus and metals

The contacted properties of metal substrates with single layer (monolayer) blue phosphorus are calculated by first principles. We analyze the charge transfer, atomic orbital overlap, electronic properties and potential barrier at the interface of metal contacted blue phosphorene (BuleP) to understand how to effectively inject electrons from the metal into the contacted blue phosphorus. We inquire into interfacial effect of blue phosphorene directly in contact with five representative metallic substrates – Au (111), Ag(111), Al(111), Co(111) and Sc(0001), which are having minimal lattice mismatch with the BlueP. We find that the contact properties of these five metals are ohmic contact and schottky contact. Of the five different contact metals, Co-BlueP heterojunction has the best electrical conductivity. The lower SBH in the Al contact can also lead to a good substrate for a Schottky contact for the heterojunction. These results can provide guidance for the future design of BlueP-based electronic devices and for the exploration of new low-dimensional semiconductor transport processes.     

Local atomic and electronic structure in the LiVPO4(F,O) tavorite-type materials from solid-state NMR combined with DFT calculations

⁷Li, ³¹P, and ¹⁹F solid-state nuclear magnetic resonance (NMR) spectroscopy was used to investigate the local arrangement of oxygen and fluorine in LiVPO₄F_1-yO_y materials, interesting as positive electrode materials for Li-ion batteries. From the evolution of the 1D spectra versus y, 2D ⁷Li radiofrequency-driven recoupling (RFDR) experiments combined, and a tentative signal assignment based on density functional theory (DFT) calculations, it appears that F and O are not randomly dispersed on the bridging X position between two X–VO₄–X octahedra (X = O or F) but tend to segregate at a local scale. Using DFT calculations, we analyzed the impact of the different local environments on the local electronic structure. Depending on the nature of the VO₄X₂ environments, vanadium ions are either in the +III or in the +IV oxidation state and can exhibit different distributions of their unpaired electron(s) on the d orbitals. Based on those different local electronic structures and on the computed Fermi contact shifts, we discuss the impact on the spin transfer mechanism on adjacent nuclei and propose tentative signal assignments. The O/F clustering tendency is discussed in relation with the formation of short V^IVO vanadyl bonds with a very specific electronic structure and possible cooperative effect along the chain.     

Vibrations of a continuous web on elastic supports

We consider an infinite, homogenous linearly elastic beam resting on a system of linearly elastic supports, as an idealized model for a paper web in the middle of a cylinder-based dryer section. We obtain closed-form analytical expressions for the eigenfrequencies and the eigenmodes. The frequencies increase as the support rigidity is increased. Each frequency is bounded from above by the solution with absolutely rigid supports, and from below by the solution in the limit of vanishing support rigidity. Thus in a real system, the natural frequencies will be lower than predicted by commonly used models with rigid supports.     

Modified Burgers-Reimschuessel model for moisture-sensitive polymers

Viscoelastic properties of moisture-sensitive polymers can be significantly affected by moisture in the ambient environment, resulting in drastic changes in the properties as the absorbed moisture content increases. In this article, a simple yet important modification to the Reimschuessel model is introduced by considering both plasticization and anti-plasticization induced by water molecules. The proposed model is validated against the results of four different polymers obtained by Onogi et al., which demonstrates its capability of describing the available data. This model can be used to estimate the performance and service life of products produced using moisture-sensitive polymers. It also reveals that small amounts of diffused moisture might have a stiffening effect on the mechanical properties of hydrophilic polymers.     

Effect of wall slip on the viscoelastic particle ordering in a microfluidic channel

The formation of a line of equally spaced particles at the centerline of a microchannel, referred as “particle ordering,” is desired in several microfluidic applications. Recent experiments and simulations highlighted the capability of viscoelastic fluids to form a row of particles characterized by a preferential spacing. When dealing with non-Newtonian fluids in microfluidics, the adherence condition of the liquid at the channel wall may be violated and the liquid can slip over the surface, possibly affecting the ordering efficiency. In this work, we investigate the effect of wall slip on the ordering of particles suspended in a viscoelastic liquid by numerical simulations. The dynamics of a triplet of particles in an infinite cylindrical channel is first addressed by solving the fluid and particle governing equations. The relative velocities computed for the three-particle system are used to predict the dynamics of a train of particles flowing in a long microchannel. The distributions of the interparticle spacing evaluated at different slip coefficients, linear particle concentrations, and distances from the channel inlet show that wall slip slows down the self-assembly mechanism. For strong slipping surfaces, no significant change of the initial microstructure is observed at low particle concentrations, whereas strings of particles in contact form at higher concentrations. The detrimental effect of wall slip on viscoelastic ordering suggests care when designing microdevices, especially in case of hydrophobic surfaces that may enhance the slipping phenomenon.     

How deeply are core electrons perturbed when valence electrons are spin polarized? The case study of transition metal compounds

The ferromagnetic and antiferromagnetic wave functions of the KMnF₃ perovskite have been evaluated quantum-mechanically by using an all electron approach and, for comparison, pseudopotentials on the transition metal and the fluorine ions. It is shown that the different number of α and β electrons in the d shell of Mn perturbs the inner shells, with shifts between the α and β eigenvalues that can be as large as 6 eV for the 3s level, and is far from negligible also for the 2s and 2p states. The valence electrons of F are polarized by the majority spin electrons of Mn, and in turn, spin polarize their 1s electrons. When a pseudopotential is used, such a spin polarization of the core functions of Mn and F can obviously not take place. The importance of such a spin polarization can be appreciated by comparing (i) the spin density at the Mn and F nuclear position, and then the Fermi contact constant, a crucial quantity for the hyperfine coupling, and (ii) the ferromagnetic–antiferromagnetic energy difference, when obtained with an all electron or a pseudopotential scheme, and exploring how the latter varies with pressure. This difference is as large as 50% of the all electron datum, and is mainly due to the rigid treatment of the F ion core. The effect of five different functionals on the core spin polarization is documented.